| Position in Line | Parameter Name | Description |
|---|
| 1 |
Station ID |
The unique numeric ID of the radar. Assigned by Rob Barnes. |
| 2 |
Year |
This and the next parameter describe the date up until which the radar configuration described in that line was valid. |
| 3 |
Seconds in Year |
This and the previous parameter describe the date up until which the radar configuration described in that line was valid. |
| 4 |
Geog. Latitude |
The geographic latitude of the radar location, given in decimal degrees to 3 decimal places. Southern hemisphere values are negative. |
| 5 |
Geog. Longitude |
The geographic longitude of the radar location, in degree given in decimal degrees to 3 decimal places. West longitude values are negative. |
| 6 |
Altitude |
The altitude above sealevel of the radar location, in meter. |
| 7 |
Scanning Boresite |
The direction of the center of the field-of-view of the radar, in degree, relative to geographic North, positive clockwise.
Traditionally, this direction was the same as the direction of the main antenna array normal. |
| 8 |
Beam Separation |
The angular separation of two adjacent beams, in degree. Normally 3.24 degrees. |
| 9 |
Velocity Sign |
The sign of the velocity direction, either +1 or -1, usually +1.(At the radar level, backscattered signals with frequencies above the transmitted frequency are assigned positive Doppler velocities while backscattered signals with frequencies below the transmitted frequency are assigned negative Doppler velocity. This convention can be reversed by changes in receiver design or in the data samping rate. This parameter is set to +1 or -1 to maintain the convention.) |
| 10 |
Attenuation Step* |
The step size of the receiver attenuation in dB. |
| 11 |
Time Difference |
The relative time delay of signal paths from the interferometer array to the receiver and the main array to the receiver, in microseconds.
tdiff = signal_travel_time_from_interferometer_to_receiver - signal_travel_time_from_main_to_receiver
If tdiff is positive, the signal travel time from the interferometer array to the receiver is longer than the travel time from the main array to the receiver. |
| 12 |
Phase Sign |
The sign of the phase shift between interferometer and main array, either +1 or -1, usually +1. (Cabling errors can lead to a 180 degree shift of the interferometry phase measurement. +1 indicates that the sign is correct, -1 indicates that it must be flipped.) |
| 13 |
Interferometer Array Position X |
The offset distance between the mid points of the interferometer and main array, in the direction along the main array, positive towards higher antenna numbers, in meter. |
| 14 |
Interferometer Array Position Y |
The offset distance between the mid points of the interferometer and main array, in the direction perpendicular to the main array, positive values indicate that the interferometer array is in front of the main array, in meter. |
| 15 |
Interferometer Array Position Z |
The offset distance between the mid points of the interferometer and main array, in the vertical direction, positive up, in meter. |
| 16 |
Receiver Rise Time* |
The rise time of the analog receiver, in microseconds. (Time delays of less than ~10 microseconds can be ignored. If narrow-band filters are used in analog receivers or front-ends, the time delays should be specified.) |
| 17 |
Stages of Attenuation* |
The maximum number of steps of analog attenuation in the receiver. (This is used for gain control of an analog receiver or front-end.) |
| 18 |
No. of Gates |
The maximum number of range gates from which the radar can receive data. Usually 75. (This is used for allocation of array storage.) |
| 19 |
No. of Beams |
The maximum number of beams the radar can form. Usually 16. Together with the scanning boresite, this parameter defined the direction of each beam relative to geographic North. (It is important to specify the true maximum. This will assure that a given beam number always points in the same direction. A subset of these beams, e.g. 8-23, can be used for standard 16 beam operation.) |
* Only valid for analog receivers, 0 for digital receivers |
Last Updated: Sun May 28 07:25:01 2023 |
